iMP1 Series
1200–1500 Watt Configurable AC-DC Power Supplies
The iMP1 series is an AC input to DC output configurable power system consisting of a microprocessor-controlled PFC front end providing seven slots that accept intelligent DC-DC converter modules with single, dual or triple outputs ranging from 2 V to 60 V. Single output modules come in four power ranges that can be mixed and matched and connected in parallel or series to obtain thousands of output combinations customized to any application. User-configurable functions include current limit and output sequencing, as well as input and output OK signals and indicators. Capable of delivering up to 1,500 watts and with up to 21 isolated outputs, the iMP1 series carries full medical safety approvals and is an extremely flexible and versatile multi-output power solution.
These digitally controlled power supplies feature a PMBus™-compliant I2C serial interface that enables parameters such as the voltage, current limit and enable/inhibit status of individual outputs to be programmed via an intuitive user GUI. The serial interface also allows remote monitoring of voltage, current and temperature.
iMP Software Package
- Specifications
- Special Features
- Models - Stock check
-
Total Max Power:
1,500 W -
Total Max Current:
300 A -
Input Voltage:
85 V to 264 V -
Output Voltage:
N/A -
Outputs:
-
Size (L x W x H):
11.000" x 8.000" x 2.500" -
Warranty:
2 years -
Operating Temperature:
-40°C to +70°C
Electrical Specifications
- Input
- Output
- Logic Control
- Isolation
- Other
- Efficiency: 85% typical depending on configuration
- Inrush Current: 40A Peak (Soft Start)
- Frequency: 47-440 Hz
- Input Range: 85-264 VAC; 120-350 VDC
- Input Fuse: 25A
- ACOK: >5mS early warning
- Holdover Storage: 20 mSec min
- Radiated EMI: CISPR 22/EN55022 Level B
- Leakage Current: 300uA Max
- EMI Filter: CISPR 22/EN55022 Level B
- Turn-on Time: AC 2,0 sec; Inhibit 150mS
- Power Factor: 0.99 typ @ full case load
- Recovery Time: To within 1% in <300uSec
- OCP: Programmable
- OVP: Programmable
- Reverse Voltage Protection: 100% of rated output
- Dynamic Response: <2% or 100mV, 25% load step
- Ripple: RMS 0.1%; P-P 1.0% to 20MHz
- Overall Regulation: 0.4% or 20mV max
- Margining: +/-4-6% of Nominal
- Programming Accuracy: +/- 5%
- Factory Set Point Accuracy: +/- 1%
- Adjust Range: +/-10% Manual; Full Range Programmable
- DCOK: +/-5% of nominal - Programmable
- Single Wire Parallel: Share within 2% of total rated load
- Thermal Protection: OTP/OTW Programmable
- Remote Sense: Compensates up to 0.5V
- Output/Output Isolation: >1 Megohm, 500V
- Safety: Meets EN60950 and EN60601
- Module Switching Frequency: 250kHz accepts external sync signal
- Full Medical Approval
- Intelligent I2C control
- Current Share on all outputs greater than 10A
- Remote Sense on all outputs greater than 2A
- Overload Protection on all outputs
- Voltage Adjustment on all outputs (Manual or Programmable)
- Margin and Remote Voltage Programming
- Global DCOK and Inhibit/Enable (Logic Programmable)
- Module DCOK and Inhibit (Logic Programmable)
- ACOK signal
- Configurable Output Sequencing
- Field Replacable Intelligent Fan
- Downloadable GUI
- Isolated 5V @ 1A Standby Output
- Active PFC
- EMI Conducted and Radiated to Class B
- Optional VME Timing and System DCOK/Reset Module
- Optional extra hold-up module
- Field Demonstrated MTBF to 550K Hours
- Digital monitor of Voltage, Current and Temp (Both Input and Output)
- Programmable voltage, current limit, fan speed, Foldback or Constant Current operation
- Optional Extended hold-up module
- External Switching Frequency Sync Input
- Optional Conformal Coating
- Industrial Temp Range (-40 to 70C)
- Industrial Shock/Vib (>50G's)
