iMP4 Series
750–1158 Watt Configurable AC-DC Power Supplies
The iMP4 series is an AC input to DC output configurable power supply system consisting of a microprocessor-controlled PFC front end providing five slots that accept intelligent DC-DC converter modules with single, dual or triple outputs ranging from 2 V to 60 V. Single output modules come in four power ranges that can be mixed and matched and connected in parallel or series to obtain thousands of output combinations customized to any application. User-configurable functions include current limit and output sequencing, as well as input and output OK signals and indicators. Capable of delivering up to 1,100 watts and with up 15 isolated outputs, the iMP4 series carries full medical safety approvals and is an extremely flexible and versatile multi-output power solution.
These digitally controlled power supplies feature a PMBus™-compliant I2C serial interface that enables parameters such as the voltage, current limit and enable/inhibit status of individual outputs to be programmed via an intuitive user GUI. The serial interface also allows remote monitoring of voltage, current and temperature.
iMP Software Package
- Specifications
- Special Features
- Models - Stock check
-
Total Max Power:
1,100 W -
Total Max Current:
220 A -
Input Voltage:
85 V to 264 V -
Output Voltage:
N/A -
Outputs:
-
Size (L x W x H):
10.000" x 5.000" x 2.400" -
Warranty:
2 years -
Operating Temperature:
-40°C to +70°C
Electrical Specifications
- Input
- Output
- Logic Control
- Isolation
- Other
- Input Range: 85-264 VAC; 120-350 VDC
- Frequency: 47-63 Hz
- Inrush Current: 40A Peak (Soft Start)
- Efficiency: 85% typical depending on configuration
- Power Factor: 0.99 typ @ full case load
- Turn-on Time: AC 2,0 sec; Inhibit 150mS
- EMI Filter: CISPR 22/EN55022 Level B
- Leakage Current: 300uA Max
- Radiated EMI: CISPR 22/EN55022 Level B
- Holdover Storage: 20 mSec min
- ACOK: >5mS early warning
- Input Fuse: 16A
- Margining: +/-4-6% of Nominal
- Programming Accuracy: +/- 5%
- Factory Set Point Accuracy: +/- 1%
- Adjust Range: +/-10% Manual; Full Range Programmable
- Overall Regulation: 0.4% or 20mV max
- Ripple: RMS 0.1%; P-P 1.0% to 20MHz
- Dynamic Response: <2% or 100mV, 25% load step
- Reverse Voltage Protection: 100% of rated output
- OVP: Programmable
- OCP: Programmable
- Recovery Time: To within 1% in <300uSec
- Thermal Protection: OTP/OTW Programmable
- Remote Sense: Compensates up to 0.5V
- Single Wire Parallel: Share within 2% of total rated load
- DCOK: +/-5% of nominal - Programmable
- Safety: Meets EN60950 and EN60601
- Output/Output Isolation: >1 Megohm, 500V
- Module Switching Frequency: 250kHz accepts external sync signal
- Full Medical Approval
- Intelligent I2C control
- Current Share on all outputs greater than 10A
- Remote Sense on all outputs greater than 2A
- Overload Protection on all outputs
- Voltage Adjustment on all outputs (Manual or Programmable)
- Margin and Remote Voltage Programming
- Global DCOK and Inhibit/Enable (Logic Programmable)
- Module DCOK and Inhibit (Logic Programmable)
- ACOK signal
- Configurable Output Sequencing
- Field Replacable Intelligent Fan
- Downloadable GUI
- Isolated 5V @ 1A Standby Output
- Active PFC
- EMI Conducted and Radiated to Class B
- Optional VME Timing and System DCOK/Reset Module
- Optional extra hold-up module
- Field Demonstrated MTBF to 550K Hours
- Digital monitor of Voltage, Current and Temp (Both Input and Output)
- Programmable voltage, current limit, fan speed, Foldback or Constant Current operation
- Optional Extended hold-up module
- External Switching Frequency Sync Input
- Optional Conformal Coating
- Industrial Temp Range (-40 to 70C)
- Industrial Shock/Vib (>50G's)
